Fluid Tech's absorbents solidify aqueous solutions across a wide range of dissolved-solids levels, converting free liquid into a solid waste form suitable for licensed disposal at permitted facilities.
Absorbent Products
AQUASET® is a granular absorbent used to solidify aqueous solutions with low-to-moderate levels of dissolved solids.
- Water, with less than 0.01 M salts or organics
- Neutralized weak acids
- Water-miscible organics
- Slurries — IX resins; filter pre-coat
AQUASET II-G™ is a versatile absorbent that is used to treat aqueous solutions with extremely high levels of dissolved solids.
- Neutralized strong acids
- Neutralized weak acids
- Water-miscible organics
Fluid Tech's Super Absorbent Polymer (SAP), or sodium polyacrylate, is used to absorb and solidify a wide variety of aqueous waste waters.
- Water, with less than 0.01 M salts or organics
- Neutralized weak acids
- Water-miscible organics
- Slurries — IX resins; filter pre-coat
ENVIRO-G® is a granular, sepiolite-based absorbent used to solidify aqueous liquids — and it absorbs oil, diesel, fuel, greases, and hydrocarbons on contact. Fluid Tech supplies it fully outfitted in two grab-and-go spill response kits, the EG-50 Spill Response Kit and the PCB/Oil Kit (FTUTG50), each housed in a weather-resistant rotomolded case.
- Oil · Diesel · Fuel
- Lubricants & Greases
- Hydraulic Fluid · Transmission Fluid · Radiator Fluids
- Antifreeze · Solvents · Paint
- PCB-Contaminated Fluids
- Organic Liquids
- Aqueous liquids (solidification)
Advantages
Volumetric efficiency
Volume increase of wastes treated using Fluid Tech products is typically less than 20%.
Leach resistance
Fluid Tech products irreversibly bind radioactive and hazardous constituents through naturally occurring ion-exchange mechanisms.
Physical integrity
Wastes solidified with Fluid Tech products maintain their physical integrity through freeze-thaw conditions.
Adaptability
Fluid Tech products are designed to be stand alone, or used in combination with one another.
What is the difference between an absorbent and a solidification agent?
An absorbent takes up free liquid and holds it as a firm, soft solid — AQUASET® is applied by simply adding it to the waste in a container. A solidification agent such as AQUASET II-H™ or PETROSET H™ goes further and sets up to a hard, load-bearing matrix. Both convert free liquid into a solid waste form suitable for licensed disposal.
Fluid Tech products are designed to be stand alone, or used in combination with one another. AQUASET® is also effective as a top-off absorbent in containers of damp or wet wastes, capturing moisture that could otherwise become a free liquid through transportation vibrations, stresses, and temperature fluctuations.
Which absorbent should I use for my waste stream?
Match the absorbent to the liquid: dissolved-solids level and whether the liquid is aqueous or a hydrocarbon decide it.
- Water with low-to-moderate dissolved solids — AQUASET®, a granular sodium montmorillonite absorbent.
- Liquids too salty or too organic for regular AQUASET® — neutralized acids and bases, and water-soluble or water-miscible organics such as alcohols, glycols, and low-molecular-weight ketones — AQUASET II-G™, a granular sepiolite absorbent.
- Aqueous waste waters and sludges for transport and disposal — FLUIDSAP 100®, a super absorbent polymer whose solidified wastes resist biodegradation and retain liquid under pressure.
- Oil, diesel, fuel, greases, and hydrocarbons on surfaces — ENVIRO-G®, a sepiolite-based absorbent that absorbs on contact and leaves surfaces dry for sweeping.
- Non-aqueous liquids in a container — oils, synthetic oils, and solvents are solidified with PETROSET II™ from the Solidification Agents line.
How much absorbent do I need per gallon of waste?
Loading rates depend on the liquid. The figures below are from the Fluid Tech Recommended Media and Loading Rate Guide; rates vary with waste chemistry.
| Waste | AQUASET® | AQUASET II-G™ |
|---|---|---|
| Water with less than 0.01M salts or organics | 4 lbs/gal | — |
| Neutralized weak acids | 4 to 6 lbs/gal (up to 0.3M) | — |
| Water-miscible organics | 5 lbs/gal (up to 5,000 mg/l) | — |
| Ethylene glycol, 0–35% | — | 8 to 10 lbs/gal |
| Ethylene glycol, 35–60% | — | 10 lbs/gal |
| Ethylene glycol, 60–90% | — | 12 lbs/gal |
Contact Fluid Tech at (423) 271-6505 for a recommendation specific to your waste stream.
Frequently asked questions
Do Fluid Tech absorbents prevent free liquids during transport and disposal?
Yes. Wastes solidified with Fluid Tech products maintain their physical integrity through freeze-thaw conditions and the vibrational stresses encountered during transportation, so no incidental or free-standing liquids develop prior to inspection at the final disposition or storage facility. The volume increase of wastes treated with Fluid Tech products is typically less than 20%.
What are Fluid Tech absorbents made of?
AQUASET® is a granular sodium montmorillonite absorbent. AQUASET II-G™ is a granular sepiolite product — greater than 90% sepiolite, with 10–15% crystalline silica (quartz). FLUIDSAP 100® is greater than 95% crosslinked sodium polyacrylate, a super absorbent polymer supplied as white, odorless granules. ENVIRO-G® is a granular, sepiolite-based absorbent.
What if my liquid is too salty or contains organics?
AQUASET® is intended for aqueous solutions with low-to-moderate levels of dissolved solids. For liquids that are too salty or contain levels of organics too high for regular AQUASET® — such as neutralized acids and bases, and water-soluble or water-miscible organic liquids — AQUASET II-G™ is the absorbent of choice.
Can absorbents be combined with solidification agents?
Yes. Fluid Tech products are designed to be stand alone, or used in combination with one another. AQUASET® is also effective as a top-off absorbent in containers of damp or wet wastes, and wastes with both water-miscible and water-immiscible components are solidified using PETROSET II™ in combination with PETROSET® or AQUASET II™.
Are Fluid Tech absorbents hazardous to handle?
Several contain crystalline silica — AQUASET® up to 6% quartz and AQUASET II-G™ 10–15% — and their Safety Data Sheets carry the signal word Danger for chronic inhalation: do not breathe dust, avoid creating dusty conditions, and use adequate ventilation. The FLUIDSAP 100® Safety Data Sheet describes a low hazard for usual industrial handling with no hazard pictograms, but still sets a respirable-dust exposure limit and warns against whirling up the material. Review each product's Safety Data Sheet in the SDS Library before use.
Not sure which absorbent fits your waste?
Tell us about your waste stream and our team will recommend the right product and treatment approach.
